Upute za upotrebu PHILIPS SRP5004

[. . . ] . 31 Picture-In-Picture (PIP) / Side-by-Side Picture (POP) . 31 Widescreen (16:9 Aspect Ratio) Viewing Modes . 39 Signal Frequency Information Display . . 47 8 8. 1 8. 2 8. 3 8. 4 8. 5 8. 6 8. 7 8. 8 9 10 TECHNICAL SPECIFICATIONS . [. . . ] In POP mode, the screen will be split in half. The screen on the left side is the main picture and the screen on the right is the sub-picture. The OSD on the upper right corner will denote the input signal source for both the main and sub-pictures. Notes: POP (4:3) Mode will preserve 4:3 aspect ratio for both images displayed in the POP windows. POP (16:9) Mode will preserve 16:9 aspect ratio for both images displayed in the POP windows. All PIP and POP related settings are also accessible using the On-Screen menu Display. Changing the Sub-Picture Position in PIP Mode Once the PIP mode is turned on; 1 Press the POSITION key to switch position. 2 Press the POSITION key repeatedly to cycle through all four corners of the screen. This function is not applicable under POP mode. Switching Main and Sub-Pictures (SWAP) You can swap the main picture and subpicture using the SWAP key. 1 Press the SWAP key once to swap. 2 Press the SWAP key again to switch back. Changing the Input Source for Sub-Picture Once the PIP or POP mode is turned on; 1 Press the SOURCE key to change the sub-picture's input source 2 Press the SOURCE key repeatedly to cycle through all available inputs for the subpicture. 31 User Manual SRP5004/4223V Changing the Input Source for Main Picture 1 Press the INPUT key or any of the DIRECT INPUT KEYS to change. Notes: PIP mode can only be turned on if the monitor's input is set to: AV1, AV2 (S-Video), Component 1 and 2. If the monitor's main input is set to RGB or DVI, the PIP and POP will not function. If the monitor's input is set to Component 1 or Component 2, the PIP will only turn on if the input signal source is compatible with 15KHz signals such as 480i and Y/CB/CR signals. When changing input source for sub-pictures to Component 1 and Component 2, only 15KHz compatible signals such as 480i and Y/CB/ CR will result in a video picture display. If another signal other than 15KHz is detected, the sub-picture may display distorted video signals. Once PIP is turned off, the next time you return on PIP mode, the position of the sub-window will start at default position. Accessing PIP and POP Modes Modes using OSD To access these modes using OSD: 1 Press the MENU +/- keys on the remote or on the front control panel of the monitor. 2 Use the ADJ +/- keys to switch to "PIP/POP" Menu. 3 Make sure that the "Picture" OSD menu below is displayed. 2 Use the ADJ +/- keys to navigate to "OTHER" OSD sub-menu as displayed below. Settings menu options: BURN-IN RECOVERY PIXEL SHIFT 6 H4222_0316 OSD Timeout Turns on OSD timer when set to ON. When set to ON, the OSD will automatically disappear from the display if no key action is detected for the set number of seconds. If set to OFF, then OSD will remain on the screen. OSD Time Setting Sets the number of seconds the OSD will remain active on the display before turning itself off. OSD TIMEOUT must be set to ON for this setting to function. OSD Background Set to OFF if you want a transparent setting. Set to ON if you want a blue background. Burn in Recovery Set to ON, if you want a full white screen to recover burn-in effects Pixel Shift Set between 1 and 5 will give a picture shift Note: To prevent permanent after-image, we strongly suggest setting the "OSD TIMEOUT" to ON. 36 User Manual SRP5004/4223V 8. 4 SLEEP TIMER SETTINGS Setting Sleep Timer Using OSD To set the sleep timer using the OSD screen: 1 Press the MENU +/- keys on the remote or the front control panel. 2 Use the ADJ +/- keys to navigate to "OTHER" OSD sub-menu as displayed below. 3 Use the MENU +/- keys to navigate to SLEEP 4 Use the ADJ +/- keys to set to ON. The monitor will function normally until the 1-minute mark. [. . . ] When the warranty on the product expires, the warranty on all replaced and repaired parts also expires. Your warranty does not cover: labor charges for removal, installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product. product repair and/or part replacement because of misuse, accident, unauthorized repair or other cause not within the control of Philips Consumer Electronics North America. reception problems caused by signal conditions or cable or antenna systems outside the unit. [. . . ]